Things You Need

  • Access to the MCB or distribution board
  • The geyser's user manual or warranty card
  • The brand's service centre number

Step-by-Step Instructions

  1. Step 1: Switch off safely

    Switch off the geyser at the wall and the MCB before checking anything.

  2. Step 2: Check power and MCB

    Make sure the switch and MCB are on. If the MCB trips again immediately, stop and call a technician.

  3. Step 3: Check the thermostat setting

    Turn the temperature knob to the middle or higher range and wait 20 minutes.

  4. Step 4: Check the inlet valve

    Make sure the cold water inlet valve is fully open.

  5. Step 5: Book service if needed

    If the light is on but water stays cold, or heating has slowed over time, book the brand's service for the element, thermostat and descaling.

Few things are worse on a cold morning than switching on the geyser and getting cold water. The good news is that many “geyser not heating” problems have simple causes – a tripped switch, a thermostat set too low, or scale on the heating element. Some problems need a technician, and a few are safety risks you should not ignore.

This guide walks through the common causes in order, from the quick checks you can do yourself to the signs that you need to call the brand’s service centre. Safety first: always switch off the geyser at the wall and the MCB before touching anything, and never open the geyser body yourself.

Quick checks (5 minutes)

  • Is the power on? Check the wall switch, the indicator light on the geyser and the MCB or fuse in your distribution board.
  • Has the MCB or ELCB tripped? If it trips again as soon as you switch on, stop and call a technician – this can mean a faulty element or wiring.
  • Is the thermostat knob set low? Many geysers have an adjustable temperature knob. Set it to the middle or higher range.
  • Did you wait long enough? A 15 L storage geyser usually needs 15–25 minutes to heat from cold, longer in winter.
  • Is the inlet valve fully open? A half-closed inlet can cause low flow and lukewarm water.

Common causes and fixes

SymptomLikely causeWhat to do
No light, no heatPower supply, switch or MCBCheck the switch and MCB; call an electrician if the socket is dead
Light on, but water stays coldFaulty heating element or thermostatCall the brand’s service centre
Water only lukewarmThermostat set low, or scale on the elementRaise the setting; book descaling
Hot water runs out quicklyTank too small, or scale reducing capacityCheck size vs family; book descaling
MCB trips when switched onElement leakage or wiring faultStop using it; call a technician
Rumbling or hissing soundHeavy scale build-upBook descaling and anode check
Water dripping from the valvePressure release valve working, or faulty valveSmall drips while heating can be normal; constant leaks need service

Scale: the most common hidden cause

In hard-water areas, minerals build up on the heating element and inside the tank. This slows heating, reduces hot water and makes the element work harder. If your geyser is a year or two old and heats more slowly than before, scale is a likely reason. Our geyser maintenance and descaling guide explains what a service visit should include, including the magnesium anode check.

When to call a technician

  • The MCB or ELCB trips repeatedly.
  • You feel a tingling or shock from taps or the geyser body.
  • The indicator light is on but the water never gets warm.
  • Water leaks from the tank body (not just the valve).
  • You see burn marks, smell burning or hear crackling at the socket.

If the geyser is under warranty, contact the brand’s authorised service centre rather than a local repair shop, so the warranty is not affected.

Repair or replace?

Replacing a heating element or thermostat is a routine repair. But if your geyser is old, the tank is leaking or rusting, or repairs keep coming back, a new geyser is usually the safer choice. A 5-star storage geyser with a good tank coating also heats more efficiently. See our guides to the best geysers in India and what size geyser you need.

Check Crompton Arno Neo 15 L Geyser on Amazon

Prevent it next winter

  • Book a service and descaling once a year in hard-water areas.
  • Keep the thermostat at 45–50°C – hot enough for bathing, with less scale.
  • Do not switch the geyser on with the inlet valve closed.
  • Make sure it is connected to proper earthing and an MCB/ELCB.

Frequently Asked Questions

1. Why is my geyser on but not heating?

If the light is on but the water stays cold, the heating element or thermostat is likely faulty. Call the brand's service centre.

2. Why does my geyser give only lukewarm water?

The thermostat may be set low, or scale may have built up on the element. Raise the setting and book a descaling service.

3. How long should a geyser take to heat?

A 15 L storage geyser usually takes about 15–25 minutes from cold; longer in very cold weather.

4. Is it safe to use a geyser that trips the MCB?

No. Stop using it and call a technician, as it can indicate an element leak or wiring fault.

Final Thoughts

Most geyser heating problems start with simple checks: power, MCB, thermostat setting and heating time. Slow or lukewarm heating often points to scale, which a yearly service fixes. If the MCB trips, you feel a shock or the light is on but the water stays cold, switch off and call the authorised service centre.