A mixer grinder jar sees more hard work than almost any other kitchen tool in an Indian home – idli and dosa batter, coconut chutney, ginger-garlic paste, wet masalas and dry spice powders, sometimes all in one day. If the jar is only rinsed and put away, food gets trapped under the blades, the rubber gasket starts to smell, and turmeric leaves a yellow stain that seems permanent.
The good news: a clean jar needs only a few minutes and things you already have in the kitchen. This guide covers a quick daily clean, a deeper weekly clean, how to remove stains and smells, and how to look after the blades, coupler and motor body so your mixer grinder lasts longer.
Every model is a little different, so always follow your mixer grinder’s instruction manual first. The steps below match the general cleaning guidance in manuals from brands such as Preethi and Bosch.
Things You Need
- Mild dish soap
- Warm water
- Baking soda
- Lemon juice or white vinegar (optional, for smells)
- Bottle brush or long-handled sponge
- Old soft toothbrush
- Soft, dry cotton cloth
Step-by-Step Instructions
-
Step 1: Unplug and remove the jar
Switch off the mixer grinder at the knob and at the wall socket, then pull out the plug. Wait until the blades stop completely before you lift the jar. Remove the lid and empty out any leftover food.
Safety note: Never clean a jar while it is fitted on the motor unit or while the plug is connected. A knob turned by mistake can start the blades.
-
Step 2: Rinse the jar straight away
Rinse the jar, lid and blades under running water as soon as you finish grinding. Fresh batter, chutney or masala washes off in seconds, but once it dries – especially under the blades – it becomes hard and needs scrubbing. If you cannot wash it immediately, at least fill it with a little water so food does not stick.
-
Step 3: Run warm soapy water in the jar
Fill the jar about one-third with warm water and add one or two drops of mild dish soap. Close the lid, fit the jar on the motor unit, plug in and run at the lowest speed for 20–30 seconds. Preethi's manual describes a similar method. This loosens food from under the blades and around the gasket without you touching the blades.
Safety note: Use warm, not hot or boiling, water. Very hot liquid can build pressure in a closed jar and push the lid open. Keep a hand on the lid while it runs.
-
Step 4: Scrub under the blades with a brush
Unplug again and remove the jar. Pour out the soapy water. Use a bottle brush or a long-handled sponge to clean the inside walls, the area under the blades and the base where food collects. Move the brush away from the cutting edges, not towards them. An old soft toothbrush reaches small gaps around the blade shaft.
Safety note: The blades are very sharp. Do not wipe them with your fingers or a cloth held in your hand.
-
Step 5: Clean the lid and the rubber gasket
Remove the gasket from the lid if your model allows it. Wash the lid, gasket and any small vent or dome with soapy water and a soft brush, paying attention to the groove where the gasket sits – this is where batter and masala hide and start to smell. Rinse well.
-
Step 6: Remove stains and smells (weekly)
For a deeper clean, mix two teaspoons of baking soda with warm water in the jar and run it for a few seconds, or rub a baking soda paste on stained areas and leave it for 10–15 minutes before washing. For strong garlic or onion smells, add a few drops of lemon juice or white vinegar to the final rinse. Rinse every part with clean water so no soap or baking soda is left behind.
-
Step 7: Wipe the motor body and coupler
With the plug out, wipe the motor body, knob and jar base area with a damp, well-squeezed cloth, then dry it with a dry cloth. Use a dry toothbrush to remove dried powder or food from the coupler (the toothed part that turns the jar) and around it. Check the power cord and plug for cuts, burn marks or loose parts.
Safety note: Do not pour water on the motor unit or spray cleaner on it. Water can enter the motor and cause a short circuit or electric shock.
-
Step 8: Dry fully and store upside down
Wipe the outside of the jar and the jar base dry. Keep the jars upside down with the lids off until they are completely dry – Bosch's manual also advises storing jars upside down. Refit the gasket only when it is dry. Store the jars empty; avoid using them as food storage containers.
Daily clean vs deep clean
| Clean | When | What it covers | Time |
|---|---|---|---|
| Quick clean | After every use | Warm water and a drop of dish soap run for a few seconds, then rinse and dry upside down | 2–3 minutes |
| Deep clean | Once a week, or after oily or strong-smelling grinding | Under the blades, the gasket and lid, stains and smells | 10–15 minutes |
| Body and base care | Once a week | Wipe the motor body, check the coupler and the cord | 5 minutes |
What not to do
- Do not put the motor unit in water or hold it under the tap. Manufacturers say to wipe it only with a damp cloth.
- Do not clean the blades with your bare fingers. Use a bottle brush or a sponge on a long handle.
- Do not put jars in the dishwasher unless your manual allows it. Some mixer grinder manuals, such as Preethi’s, say the jars are not dishwasher safe.
- Do not use steel wool or harsh scrubbers on the jar, lid or body. They scratch the surface, and scratches hold stains and smells.
- Do not leave the jar soaking for hours. The blade shaft sits on a bearing or bush inside the jar base. Water that gets in there can, over time, cause rust or a stiff blade.
Removing turmeric and masala stains
Turmeric is the most common reason a white lid or gasket turns yellow. Wash the part as soon as possible after grinding – fresh stains come off much more easily. For an old stain, rub a paste of baking soda and a little water on the area, leave it for 10–15 minutes and wash it off. Drying the lid and gasket in sunlight also helps, because the yellow colour in turmeric fades with light. Some light staining on plastic parts may stay, but it does not affect how the jar works.
Removing garlic, onion and spice smells
Smells usually live in the rubber gasket and under the blades, not in the steel jar. Remove the gasket if your model allows it and wash it separately. Run the jar with warm water and a spoon of baking soda for a few seconds, then rinse. A few drops of lemon juice or white vinegar in the rinse water can also help with strong smells. Always let the jar, lid and gasket dry fully before you put them back together – a closed, damp jar is what makes smells come back.
Caring for the blades
Mixer grinder blades are made of stainless steel and are designed to work for years without sharpening. If grinding takes longer than it used to, first check for dried food under the blades, a loose blade or a worn coupler – cleaning and a tight assembly often bring the performance back. You may see advice to grind rock salt to sharpen the blades. We did not find this advice in the manufacturer manuals we checked, and hard salt can scratch the jar, so we suggest avoiding it. If a blade is bent, chipped or wobbles, stop using the jar and contact the brand’s service centre for a replacement blade assembly or jar.
When to replace parts
Replace the gasket if it is cracked, has gone hard or the jar leaks from the lid even when it is closed properly. Replace the coupler if the jar slips, makes a grinding noise or the coupler teeth look worn or broken. Use parts from the brand’s authorised service centre or official store so that the size and fit are correct. If you are choosing a new mixer grinder, our guide to the best mixer grinders in India compares jar quality, warranty and service support across popular models.
Frequently Asked Questions
1. How often should I deep clean my mixer grinder jar?
Once a week is enough for most homes. Clean it sooner if you have ground something oily or strong-smelling, like garlic paste or fish masala, or if you notice a smell from the gasket.
2. Can I wash mixer grinder jars in a dishwasher?
Only if your instruction manual says the jars are dishwasher safe. Some mixer grinder manuals, such as Preethi's, say the jars are not dishwasher safe. Hand washing is the safer choice for the jar, blades and gasket. The motor unit must never go in water or a dishwasher.
3. How do I remove the smell from a mixer grinder jar?
Most smells come from the rubber gasket and dried food under the blades. Remove and wash the gasket, run the jar with warm water and baking soda for a few seconds, and add a little lemon juice or vinegar to the final rinse. Let all parts dry fully before closing the jar.
4. Does grinding salt sharpen mixer grinder blades?
This is a common tip, but we did not find it in the manufacturer manuals we checked. Mixer grinder blades are designed to work for years without sharpening. If grinding is slow, check for dried food under the blades, a loose blade or a worn coupler. Contact the brand's service centre if a blade is damaged.
5. Why does my mixer grinder stop suddenly while grinding?
Many mixer grinders have an overload protector that switches the motor off when the jar is overfilled or the motor gets too hot. Switch off and unplug, remove some of the contents, let the motor cool for a few minutes, then press the reset button (usually on the bottom of the motor unit) if your model has one. Check your manual for the exact steps.
6. Can I clean the jar with hot water?
Use warm water, not very hot or boiling water. Very hot liquid in a closed jar can build pressure and push the lid open, and very high heat can also affect the gasket over time.
Final Thoughts
A clean mixer grinder jar comes down to a simple habit: unplug, rinse right after use, clean under the blades and the gasket once a week, and dry everything upside down before storing. Keep water away from the motor unit, keep your fingers away from the blades, and follow your model's instruction manual. These few minutes keep your chutneys and batters tasting fresh and help your mixer grinder last for years.
